Basic HTML Version
TEST/DIAGNOSTIC PROCEDURES
(Continued)
SOLENOID TEST.
1. (From Lamp Test) Using AUTO-UP, press ADVANCE. Observe that the Player 1 and 2 displays
show the message, COIL TEST, the Player 3 display shows 05 (Solenoid Test identifier). Next,
the Player 3 display shows a series of test steps from 01 through 22, while the Player 1 and 2
displays show the solenoid/circuit name. During each of these steps, pulsing of the respective
solenoid/circuit occurs. The test cycles repeatedly, unless halted via the MANUAL-DOWN
switch. Refer to the
Solenoid Table
for solenoid numbers and wiring information.
CPU
Board connections at 1P11, 1P12, and 1P19 are also listed in the table.
To continuously pulse a single solenoid/circuit, use MANUAL-DOWN. Press ADVANCE to
sequence through the switched, controlled, and special solenoids. Use AUTO-UP to resume
test cycling, and to proceed to the next test.
1l1aek
~ntgl.lt 2000
Solenoid Table
Sol.
Wire
1
Connections
Driver
Solenoid Part Number
Function
Solenoid
Playfieldl
Flashlamp Type
No.
Type
Color
CPU Bd
Trnstr
Cabinet
i-Insert Bd: p+Playhetd
01A3 Outhole Kicker
Switched Vio-Brn } 1Pll-1
5J1-9; 5J4-9 (A)
Q33 AE-23-800
01C3 UPF Big Red Bolt Flasher
Switched Blk-Brn (Gry-Brn)
5J5-9 (C)
Q33
#906/#89
flashlamps 2p,2i
02A 3 Ball Release (Shtr Lane Feeder) Switched Via-Red}
1PI'-3
5J1-7: 5J4-8 (A)
Q25 AE-23-800
02C3 UPF Big Blue Bolt Flasher
Switched Blk-Red (Gry-Red)
5J5-8 (C)
Q25
#906/#89
flashlamps 2p,2i
03A 3 Left 3-Bank Drop Tgt Reset
Switched Via-om}
1PI'-4
5J1-6: 5J4-7 (A)
Q32 AE-26-1200
03C 3 Bolt Circle Center Flasher
Switched Blk-Orn (Gry-Orn)
5J5-7(C)
Q32
#906/#89
flashlamps 2p.2i
04A3 Right 3-Bank Drop Tgt Reset
Switched Via- Yel}
1PI'-5
5J1-5: 5J4-6 (A)
Q24 AE-26-1200
04C3 Flipper Lane Flasher
Switched Blk-Yel
(Gry-Yel)
5J5-5 (C)
024
#906/#89
lIashlamps 2p.2i
05A 3 Not Used
Switched Via-Grn } 1P11-6
5J1-4: 5J4-5 (A)
031
05C 3 Drop Target Rasher
Switched Blk-Grn (Gry-Gm
5J5-4 (C)
031
#906/#89
lIashlamps lp.2i
06A 3 Ball Popper
Switched ViO-BIU}
1Pl'-7
5J1-3: 5J4-4 (A)
023 AE-23-800
06C3 LPF Ramp Flasher
Switched Blk-Blu (Gry-Blu)
5J5-3 (C)
023
#906/#89
flashlamps 2p.21
07A 3 UPF Lockup Kickback
Switched ViO-Blk}
, P' 1-8
5J1-2: 5J4-2 (A)
030 AE-24-900
07C 3 Right Eject/Upr Flipper Flashers Switched Blk-Vio (Gry-Vio)
5J5-2 (C)
030 #89 flashlamps
1p.zi
08A 3 Right Eject
Swilched Vio-Gry } 1PI'-9
5Jl-1: 5J4-1 (A)
Q22 AE-26-1500
08C 3 UPF Lockup Kickback Flasher
Switched Blk-Gry (Gry-Blk)
5J5-1 (C)
022
#906/#89
flash lamps , p.2i
09 Insert Board Gnlilium Relay
Controlled Brn-Blk 1P12-1 5J2-9: 5J6-9: 2J4-3 Q17 5580-09555-01 4a
10 UPF Gnl Ilium Relay
Controlled Brn-Red 1 P12-2 5J2-8: 5J6-8: 2J4-5
Q9 5580-09555-01 4a
11 LPF Gnl ilium Relay
Controlled Brn-Orn lP12-4 5J2-6: 5J6-7: 2J4-6
Q'6 5580-'2'45-01
41>
12
NC
Select Relay
Controlled Brn-Yel
lP12-5
5J2-5
Q8 5580-09555-01 5
'3
Kickback (L Outlane)
Controlled Brn-Grn 1 P12-6
5J2-4: 5J6-5
015 AE-23-800
14 Knocker
Controlled Brn-Blu 1P12-7
5J2-4: 5J6-3
Q7 AE-23-800
15 Magna Save
TW
Driver
Controlled Brn-Vio 1P12-8
5J2-2: 5J6-2
014 C-12493
16 Motor Targets (UPF) Relay
Controlled Brn-Gry 1P12-9
5J2-1: 5J6-1
Q6 5580-12'
45-01 4b
17 Left Jet Bumper
Special #1 Blu-Brn 1P19-7
5J3-7: 5J7-7
Q75 AE-23-800
'8
Left Kicker (OslingO)
Special #2 Blu-Red 1P19-4
5J3-6: 5J7-6
071 AE-26-'
500
'9
Right Jet Bumper
Special #3 Blu-Orn , P19-3
5J3-3: 5J7-3
Q73 AE-23-800
20 Right Kicker ("slingO)
Special #4 Blu-Yel
1P19-6
5J3-4: 5J7-5
Q69 AE-26-'500
21 Lower Jet Bumper
Special #S Blu-Grn , P19-8
SJ3-2:SJ7-2
077 AE-23-800
22
Not Used
Special #6 Blu-Blk 1P19-9
5J3-1: 5J7-1
079
-
Righi flipper
-
Orn-Vio 1P19-1
2J5-5: 2Jl0-7
Lower Right Flipper
[Blu-Vio]2
[2Jl0-l: 2J8-15!
FL 11630150VDC
Upper Righi Flipper
[Blk-Yel]
[2Jl 0-4:2J8-
j
2]
FL 11630150VDC
-
I eft Flipper
-
Orn-Gry 1P19-2
2J5-4: 2Jl 0-8
Lower Left Flipper
[Blu-Gry] 2
[2Jl0-2:2J8-4]
FL 11630150VDC
~
1. Wire colors. except flipper Orn-Vic and Orn-Gry, are ground connections (to coil terminal with unbanded end of diode). Flipper Orn-Vio and
Orn-Gry wires connect from CPU Board to flipper switch. 2. Flipper connections shown in braces are from flipper switch to flipper coil. 3. "A"
circuits are pulsed. when Sol. 12 is de-energized; "COcircuits are pulsed. with Sol. 12 energized. Wire colors in brackets are those from respective A
and C terminals corresponding to the J1-terminal connection listed for the Aux Power Driver Bd, which controls the device pulsing by Sol. 12
4. Relay is mounted on Relay Bd. (4a) pin C-11998-1; (4b) C-11902-1. 5. Relay is mounted on Aux Power Driver Bd, 0-12247 in th" backbox.
JUadt
1utgbt 29