• November 28, 2023, 04:07:51 AM

Login with username, password and session length

NOTE: This forum is for respectful dialog and it's content is meant to be kept on this site - so please be respectful and please do not copy content to other sites.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Ding

Pages: [1]
1
MMR Support [MMR Members Only] / Re: Problem With Ball Trough
« on: July 30, 2022, 11:43:55 AM »
Lloyd,


Thanks for your help with this problem. The ring on the coil sleeve had broken off and the sleeve was slipping up into the trough obstructing ball flow. I replaced the sleeve and now it works perfectly.

2
MMR Support [MMR Members Only] / Re: Problem With Ball Trough
« on: July 19, 2022, 11:16:40 AM »



After initially being solved, this problem has unfortunately returned. The balls are again getting stuck in the Ball Trough by the black plastic ring around the coil ejector device. Lloyd, last time I fixed this by loosening the 4 screws on the bracket holding the coil and plunger and moving the bracket down so that the balls could clear the black plastic tube. Unfortunately, the bracket is moved down as far as it will go but the balls are still being obstructed. What is my next step for solving this problem? Is this a problem with the Coil/Plunger device and this needs to be replaced? Do I need to somehow enlarge the sheet metal holes that each of the 4 screws from the bracket sits in so that I can shift the bracket a little farther?

3
MMR Support [MMR Members Only] / Re: Left Troll Problem
« on: February 19, 2020, 10:25:47 AM »
Thanks!

4
MMR Support [MMR Members Only] / Left Troll Problem
« on: February 16, 2020, 09:38:32 PM »





My left troll isn't registering hits. I found two screws and a double holed washer on the playfield. The face of my left troll is totally loose. Just flapping around.


I found the attached picture that Lloyd had posted on another forum. Obviously I need to reattach these 2 screws and the washer to the back of the face of my left troll to hold it in place. However, what are the 2 screws attached to? It is attaching the face of the troll to the long arm of the switch? I just can't make that out from the picture. Is the washer under the screw heads but above the long arm of the switch?




5
MMR Support [MMR Members Only] / Re: Problem With Ball Trough
« on: August 13, 2018, 08:57:52 AM »
Thanks Lloyd. That worked perfectly!

6
MMR Support [MMR Members Only] / Problem With Ball Trough
« on: August 09, 2018, 08:21:41 PM »
I'm having an issue with balls getting stuck in the Ball Trough. The coil ejector device that ejects the ball out of the Ball Trough has a black plastic ring around it (Coil Tubing?). It appears that this black plastic tube is extending a little too far up into the ball trough obstructing the balls from being right over the plunger so that they can be ejected from the Trough. I can push the black plastic tube down a little to relieve the obstruction, but it keeps recurring. Any ideas how to fix this?

7
The ball keeps getting stuck, just below the I (in F-I-R-E) at the left return lane switch. It looks like the metal switch is sticking up too much into the playfield, and the ball just can't get over it. Am I going to do any damage if I try to bend the metal switch downward a little, so the ball can get over it, or is there another way to adjust it?

8
MMR Support [MMR Members Only] / Re: Black Plate in Coinbox
« on: July 04, 2016, 10:07:22 PM »
Can this be installed when the game is in use? There is no hole for the cord when the plate is on. Can't understand why this would ever be installed?

Pages: [1]