• March 28, 2024, 02:45:25 PM

Login with username, password and session length

NOTE: This forum is for respectful dialog and it's content is meant to be kept on this site - so please be respectful and please do not copy content to other sites.

Author Topic: Problem With Ball Trough  (Read 14244 times)

Offline Ding

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 8
  • Karma: +0/-0
    • View Profile
Problem With Ball Trough
« on: August 09, 2018, 08:21:41 PM »
I'm having an issue with balls getting stuck in the Ball Trough. The coil ejector device that ejects the ball out of the Ball Trough has a black plastic ring around it (Coil Tubing?). It appears that this black plastic tube is extending a little too far up into the ball trough obstructing the balls from being right over the plunger so that they can be ejected from the Trough. I can push the black plastic tube down a little to relieve the obstruction, but it keeps recurring. Any ideas how to fix this?

Offline Lloyd Olson

  • LTG : )
  • Global Moderator
  • Three Star Member
  • *****
  • Posts: 385
  • Karma: +18/-7
    • View Profile
Re: Problem With Ball Trough
« Reply #1 on: August 10, 2018, 12:07:42 AM »
Hello 

The coil and plunger is fastened to a bracket. This bracket is fastened to the end of the ball trough by four screws on the opposite side of the coil. Loosen them and move the whole bracket down a tiny bit. Not too much.
Do that and you should be good to go.
Thank you,LTG : )

Offline Ding

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 8
  • Karma: +0/-0
    • View Profile
Re: Problem With Ball Trough
« Reply #2 on: August 13, 2018, 08:57:52 AM »
Thanks Lloyd. That worked perfectly!

Offline Ding

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 8
  • Karma: +0/-0
    • View Profile
Re: Problem With Ball Trough
« Reply #3 on: July 19, 2022, 11:16:40 AM »



After initially being solved, this problem has unfortunately returned. The balls are again getting stuck in the Ball Trough by the black plastic ring around the coil ejector device. Lloyd, last time I fixed this by loosening the 4 screws on the bracket holding the coil and plunger and moving the bracket down so that the balls could clear the black plastic tube. Unfortunately, the bracket is moved down as far as it will go but the balls are still being obstructed. What is my next step for solving this problem? Is this a problem with the Coil/Plunger device and this needs to be replaced? Do I need to somehow enlarge the sheet metal holes that each of the 4 screws from the bracket sits in so that I can shift the bracket a little farther?
« Last Edit: July 19, 2022, 11:18:32 AM by Ding »

Offline Lloyd Olson

  • LTG : )
  • Global Moderator
  • Three Star Member
  • *****
  • Posts: 385
  • Karma: +18/-7
    • View Profile
Re: Problem With Ball Trough
« Reply #4 on: July 19, 2022, 12:19:41 PM »
Hello
Has the top hat part of the coil sleeve broken off the bottom and the coil sleeve slipped up ? If so new coil sleeve. If not, trim the coil sleeve shorter.
Thank you,Lloyd

Offline Ding

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 8
  • Karma: +0/-0
    • View Profile
Re: Problem With Ball Trough
« Reply #5 on: July 30, 2022, 11:43:55 AM »
Lloyd,


Thanks for your help with this problem. The ring on the coil sleeve had broken off and the sleeve was slipping up into the trough obstructing ball flow. I replaced the sleeve and now it works perfectly.