• March 29, 2024, 03:14:00 AM

Login with username, password and session length

NOTE: This forum is for respectful dialog and it's content is meant to be kept on this site - so please be respectful and please do not copy content to other sites.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Lloyd Olson

Pages: 1 ... 14 15 [16] 17
226
MMR Support [MMR Members Only] / Re: Flaky Switches?
« on: April 21, 2015, 04:02:18 PM »
Please don't worry.

Should a problem arise PPS and CGC will work hard to help you.

LTG : )

227
MMR Support [MMR Members Only] / Re: MMR Sound Issue
« on: April 18, 2015, 01:15:34 PM »
I would start with reseating any audio connectors. Power and signal.

Thank you.
LTG : )

228
Please try adjusting the power first.

Thank you,
LTG : )

229
Hello

This was on the ticket you opened and I posted information to help you.

Thank you,
Lloyd

230
Hello

I responded help to the ticket you opened.

Thank you,
Lloyd

231
MMR Support [MMR Members Only] / Re: Catapult Issue?
« on: April 16, 2015, 09:27:55 PM »
You can loosen the wireform and aim it better.

Or in CGC settings make the catapult coil strength one notch stronger.

LTG : )

232
MMR Support [MMR Members Only] / Re: Catapult Issue?
« on: April 15, 2015, 02:47:01 PM »
You are not allowed to view links. Register or Login
Bought My AMG ....didn't take it back to Mercedes for Tweaking ..

Your Mercedes dealer did the tweaking. Car dealers go through them and make adjustments and corrections so you don't get out on the road and kill yourself.

Stern is tops in quality control. And the games then go to CGC for more of the same.

Then they get put in a truck and bounced around the country to you. Things can happen beyond anyone's control.

And from what I've seen in tech support so far. With 100+ games out there, the problems have been few and far between.

PPS/CGC/ with Stern assembling, are doing a good job to deliver you the best pin they can.

LTG : )

233
MMR Support [MMR Members Only] / Bill Validator
« on: April 15, 2015, 01:30:53 PM »
For anyone wanting to install a bill validator, here is what I found that works quite nicely.

ICT  US4 12 Volt 300 capacity.

Larger capacity won't let you close the coin door.

LTG : )

234
MMR Support [MMR Members Only] / Re: MMR Shaker not working
« on: April 14, 2015, 05:08:53 PM »
Hello Tim

On page 1-56 in the manual, it is CR2 on the power supply board.

I mention the manual to help reference it.

LTG : )

235
MMR Support [MMR Members Only] / Re: Catapult Issue?
« on: April 14, 2015, 05:02:51 PM »
You may need to raise or lower it a little. Washers work good.

LTG : )

236
MMR Support [MMR Members Only] / Re: MMR Shaker not working
« on: April 14, 2015, 01:13:04 PM »
The old one most likely took out it's fuse.

Right inside the coin door on the right side is the power supply for it, please see if the LEDs next to the fuses are lit.

Thank you,
LTG : )

237
MMR Support [MMR Members Only] / Re: Catapult Issue?
« on: April 14, 2015, 12:34:59 AM »
There is a bolt on a hex post holding the catapult wireform by the left tower. Loosen it and move the wireform to aim the ball away from the rear tower.

LTG : )

238
MMR Support [MMR Members Only] / Re: Catapult Issue?
« on: April 13, 2015, 01:24:56 PM »
Two thoughts come to mind.

You can loosen all the places where the wireform fastens down and aim it better.

And if need be in the CGC settings ( hold the escape button down to get into them, 5 seconds or so ) you can make the catapult coil stronger in there.

Thank you,
LTG : )

239
MMR Support [MMR Members Only] / Re: MMR Shaker not working
« on: April 09, 2015, 02:03:05 PM »
It should be coming. Doug said he sent it.

LTG : )

240
MMR Support [MMR Members Only] / Re: Ball gets Stuck in Damsel Tower
« on: April 02, 2015, 06:11:58 PM »
I'm sorry. First thing you might check is the post below the playfield that goes up and holds the ball in the tower.

I'd check that first to see it moves freely.

LTG : )

Pages: 1 ... 14 15 [16] 17